How Do I ... Setup 'uwosecure-v2' network access on Mac Lion (10.7)

 


Introduction

This document will help you setup uwosecure-v2 on Mac Leopard 10.7.

First...

Make sure that your Western Identity Manager password has been synchronized here.

Procedure

You will first need to make sure you are using MAC OS X version 10.7.4 

(To check this, click on the Apple button (in the upper left corner of your screen) and select "About this Mac." If it has version 10.7 but not 10.7.4, you can simply update OS X but clicking on the apple button in the upper left corner of your screen and select "Software Update".  This should bring your copy of Lion up to its latest version.  You will need to perform this either at home with an internet connection, or hard-wired on campus.) 

 

There are two methods for OS X Lion to connect to the uwosecure-v2 wireless network.  Attempt to use Method #1 first.  If it does not work, please try Method #2.

 

Method #1:

1. Click on the Wireless Network symbol at the top right of your screen.

2. Make sure your Airport is turned on.

3. Click on 'uwosecure-v2'.

4. Change the following:

           Mode: leave as 'Automatic'
           Username: your Western username
           Password: your Western username

 

5. Click 'Join'.

 

 

 

6. An authentication certificate may pop up.  If it does, click 'Continue'.

 

 

7.  You should now be connected to the 'uwosecure-v2' wireless network.  If you have any difficulty with this method, please attempt Method #2.

 

Method #2

1. Click on the Wireless Network symbol at the top right of your screen.

2. Click 'Turn Airport Off'.

3. Click on the Wireless Network symbol again then click 'Open Network Preferences'.

 

 

 

4. In the Network window that opened up, click on 'Advanced'.

 

 

 

5. Remove any networks that you do not use that are listed in the 'Preferred Networks' area by highlighting the network then clicking the "-" button.

 

 

 

6. Select the '802.1X' tab at the top. Remove any uwo/uwosecure related user profiles by selecting the network in the list then clicking the '-' symbol at the bottom. 

7. Click on '+', then select 'Add User Profile'

8. Rename it to 'uwosecure-v2'.

 

 

9. On the right side, change the following:

           User Name:  your Western username
           Password:  your Western password
           Wireless Network: uwosecure-v2
               (You will have to type this in manually as there will be no networks shown in the dropdown menu.)
           Authentication: uncheck TTLS, and make sure PEAP is the only option checked.  

 

 

 

10. Now, return to the 'Airport' tab to continue.

11. Underneath the 'Preferred Networks' list, click the '+' button.

 

 

 

12. For Network Name, enter the following:

           Network Name:  uwosecure-v2
           Security:  WPA2 Enterprise
           User Name:  Do Not Enter
           Password:  Do Not Enter
           802.1X:  Choose 'uwosecure-v2'
            (This will populate the username and password fields automatically)

 

 

 

13. Select 'Add' then 'OK' and then 'Apply'
      (Note: If you also see a “TLS Certificate”, ignore it and continue)

14. Click 'Turn Airport On'

15. Now you will need to allow airport to connect itself to uwosecure-v2 which may take a few minutes.

16. An authentication certificate may pop up.  If it does, click on 'Show Certificate'.

 

 

 

17. Check mark 'Always trust "radical.vm.its.uwo.ca"' and click 'Continue'.

 

 

 

You should now be set up for 'uwosecure-v2' network access.

 


Western provides the best student experience among Canada's leading research-intensive universities.