How Do I ... Connect Windows 2000 to the UWO Network

Introduction

This document describes how to connect a Windows 2000 machine to the Campus Backbone Network (and the Internet). An example of such an on-campus connection is a PC in an office at UWO that has a direct backbone connection. To connect the Windows 2000 machine to the RezNet network, all the same steps apply with the exception of the configuration of the TCP/IP protocol. Configuration for RezNet is included in section 3.2.2.

WARNING: You must have your Windows 2000 installation diskettes or CD-ROM handy in order to correctly install the networking components (some sections require copying files from the installation disks). If you do not have them, do not proceed with the instructions in this document.

Requirements:

Windows 2000 and a network card installed.
The PC must be registered in the DNS and have an IP number.
If the machine will be using RezNet, the student must have gone through the on-line registration process which will generate an IP number on RezNet for them.

Installation

Verify that the appropriate client and protocols are installed:

Click Start, point to Settings, and then click Network and Dial-up Connections. Click Local Area Connection, and then click Properties on the File menu. Check the Components checked are used by this connection box.

You may see the following components:

Client for Microsoft Networks. This is the entry for the Microsoft client. It is only necessary if you want to run a peer-to-peer network.
SMC EtherCard Plus.... This is the entry for the network card (network adapter) you have in the PC (e.g. an SMC card).
TCP/IP. This is the protocol for the Internet.
NetBEUI. This is the protocol for the Microsoft peer-to-peer network.

Install the Network Adapter

If Windows 2000 was installed with the network card (adapter) present, the correct driver for that card should already be installed. Plug and Play network cards (such as SMC EtherPower 8432) will automatically be detected by Windows 2000.

If you need to install the driver now, please follow the steps below:

Click Start, point to Settings, click Control Panel, and then double-click Add/Remove Hardware.
Click Next, click Add/troubleshoot a device, and then click Next.
In the Devices box, click Add a new device, click Next, click No, I want to select the hardware from a list, and then click Next.
In the Hardware types box, click Network Adapters, and then click Next.
Click the appropriate network adapter manufacturer and model, click Next, click Next, and then click Finish.
Restart your computer.

Install the Clients

To install the clients, follow the instructions below:

Click Start, point to Settings, and then click Network and Dial-up Connections.
Click Local Area Connection, and then click Properties on the File menu.
Check the Components checked are used by this connection box. If this box is empty, you must install clients.
Click Install.
Click on Client , then click on Add, click on Client for Microsoft Networks.
Click OK.
Allow the computer to restart.

Install the Protocols

To install the protocols, follow the instructions below:

Click Start, point to Settings, and then click Network and Dial-up Connections.
Click Local Area Connection, and then click Properties on the File menu.
Click Install.
Click on Protocol , then click on Add, click on TCP/IP.
Click OK.
Allow the computer to restart.

Configuration

Configure the Network Adapter

In the Control Panel , double click the Network and Dial-up Connections icon.
Click Local Area Connection, and then click Properties on the File menu. Below the network card adapter (e.g. SMC EtherCard PLUS).
Click the Configure button.
In the General tab, make sure that the Device status states that the device is working properly.
Click the Resources tab. You will find the I/O address range, the IRQ Interrupt and Memory Address settings here.
Click OK

NOTE: For older network cards, the information in the Resources section may not be correct. You need to check the correct network card settings using the diagnostic program that came with the card (e.g. ezstart) and input them into this section. You can run the diagnostic program from a Command prompt window. Windows 2000 should automatically recognize the information on newer plug and play cards.

Finding the Network Card Address

Click the START button and choose Run.... Enter

	command

This will give you a pop up black box. Type in

 	ipconfig /all

This should give you the IP information including the network card address.

The correct network card address should be registered in the DNS file.

Configure the TCP/IP Protocol for accessing the Internet

Click Local Area Connection, and then click Properties on the File menu. Click on Internet Protocol (TCP/IP). Click the Properties button.

This will give the TCP/IP Properties window. Do not click OK until you configure all the sections below otherwise you will be exited from the Properties window.

There are two ways to configure the TCP/IP Protocol - Static and Dynamic (DHCP) configuration. Using Dynamic IP configuration is simpler, easier to maintain and more flexible when configurations change.

Static IP Configuration

At many sites each machine is assigned a static configuration which will not change -- or at least should not change that often. You should talk to your site manager first to obtain the configuration information for your system. At those sites follow these instructions:

Note well: the Reznet does NOT assign static configurations. See below for instructions on using Dynamic IP Configuration

In General

Click 
Use the following IP address
Fill in your IP address (129.100.xxx.yyy)
Fill in the Subnet mask (255.255.255.0)
Fill in Default Gateway (129.100.xxx.1)

Click 
Use the following DNS server addresses
type 129.100.2.12 in preferred DNS server
type 129.100.2.51 in Alternate DNS server

Click Advanced.. in the bottom right corner

IP Settings tab
You should see the information in IP address, Subnet mask and Default gateways listed the same as you've entered from above.
DNS tab
```
In "DNS server addresses, in order to use:", you should see:
```
```
	129.100.2.12
 	129.100.2.51
```
```
Click 
Add
type 129.100.10.252 and click 
Add
```
Click on: Append these DNS suffixes (in order)
```
Click 
Add
type uwo.ca and click 
Add
```
Check mark: Register this connection's addresses in DNS
Each time you click the Add button, the entry you just typed in will appear in the box below.
WINS tab
Below in WINS addresses, in order of use:, it should be a white box
The following lines should be checked or marked:
```
 	Enable LMHOSTS lookup

	Enable NetBIOS over TCP/IP
```
Options tab
Under Optional settings, Click on IP security and then click on Properties
Make sure Do not use IPSEC is marked then click OK
Click on TCP/IP filtering and then click on Properties
Make sure Enable TCP/IP Filtering (All adapters) is NOT marked and Permit All is marked on 3 columns.
Then click OK.

Dynamic IP Configuration

At many sites (e.g. on the Reznet) machines are dynamically configured by a central DHCP server (some sites support their own DHCP server, others rely on a central DHCP server managed by ITS). You should talk to your site manager first to determine if the site supports dynamic configuration. At those sites follow these instructions:

In General

Click 
Obtain an IP address automatically

Click 
Obtain DNS server address automatically

Click 
Advanced.. in the bottom right corner

IP Settings tab
You should see DHCP Enabled below the IP address column and blank below on Default Gateways.
DNS tab
In "DNS server addresses, in order to use:", you should see blank in the white box

The following lines should be marked or checked:

Append primary and connection specific DNS suffixes
Append parent suffixes of the primary DNS suffix
Register this connection's addresses in DNS
WINS tab
Below in WINS addresses, in order of use:, it should be a white box

The following lines should be checked or marked:
```
 	Enable LMHOSTS lookup

	Use NetBIOS setting from the DHCP server
```
Options tab
Under Optional settings, Click on IP security and then click on Properties

Make sure Do not use IPSEC is marked then click OK

Click on TCP/IP filtering and then click on Properties

Make sure Enable TCP/IP Filtering (All adapters) is NOT marked and Permit All is marked on 3 columns.

Then click OK.

Click the OK button at the very bottom of the screen (it may be partially obscured). This will save all the above settings and exit from the Properties window back to the Network window. Click OK to exit. You may be asked to restart Windows 2000.

Using IP Applications

Make sure you have followed the instructions in section 3.2 Configure the TCP/IP Protocol for accessing the Internet. You can now run 16 and 32 bit IP (Internet).

Connect to a Novell server

If you want to connect to a novell server, please contact the ITS helpdesk at 519-661-3800 for installation and configuration. Those with RezNet connections should skip this section.

Error & Information for new computers

If you are unable to connect to the network backbone, please record the error message and contact ITS helpdesk at 519-661-3800.

Note: For faculty/staff - You need to contact the helpdesk to register your computer if your computer is new before you can connect.

For Reznet - You will have to register your computer by clicking onto the browser once you connect the cable from your computer to your room before you can connect.

Disclaimer: The provided instructions are for information purposes only. Neither The University of Western Ontario nor the Division of Information Technology Services assume any responsibility for loss of use or damage to a computer system (including any data or software contained within the computer system) which is the result (directly or indirectly) of the application of these instructions. Any problems, questions or concerns not addressed by these instructions should be directed to the vendor and/or the manufacturer and not to The University of Western Ontario or any of its employees or incumbents.

©2010, The University of Western Ontario. Permission is granted to copy in whole or in part provided that due credit is given to the authors, Information Technology Services, and The University of Western Ontario.

Finding Your Way